A Basic Guide To Seed Starting For Hydroponics
The beauty of hydroponics is that it allows you to have complete control over every input that goes into your plants: be it air, water, light, or nutrients.
You may have tasted success in your first grow system, or you may be in the process of building one now. We all know the drill.
A lot of hard reading and research, and multiple trips to your local Home Depot or gardening supply store, time spent creating your system from scratch. It is all worth the effort.
But where did you get your first plants from? The chances are that you got them as seedlings or runners from the local store.
Buying pre-grown seedlings/saplings is a good option for beginners. But in the long run, learning to start with your own batch of seeds is the best option.
Today, we will examine why this is so, and also look at all the processes involved.
Why Seeds Are Better Than Seedlings From Stores
Remember what we said at the beginning, about how hydroponics gives you complete control over all the inputs? Well, seeds are also inputs, aren’t they?
They are arguably the most important input, as they decide the type of plants and the productivity of your final harvest as well. So why would you want to leave this all-important aspect in the hands of others?
First and foremost, it is a question of freedom and choice. When buying seedlings from a store, you are dependent on their catalog. They may or may not have the varieties you seek.
Seeds are more abundant and easier to get. In fact, some rarer heirloom plants are often available only as seeds.
Cleaner (Less Trauma Involved)
When you do the seed starting process at home, you can plan ahead and create seedlings in a soilless medium. But when you buy from a store, you cannot guarantee that.
As you may very well know by now, soil and hydroponic systems do not go together. Soil can contain contaminants. Seedlings planted in the soil will have to go thorough rinsing and cleaning.
And if you are not careful, that can damage the fragile roots of young seedlings. When you start with seeds, this complication does not arise.
This one is pretty straightforward. Buying seeds are always cheaper than buying seedlings of the same plant.
Getting seeds started takes time and effort. And you can bet that the local store or nursery will charge you extra for that. Start at home, and you can avoid this middleman.
If you want to do legit hydroponics, you have to learn how to start your own seeds. It is an integral part of growing plants.
When you buy pre-grown seedlings, it almost feels like cheating. Plus, watching a plant grow from a tiny seed will give you more satisfaction than a seedling that someone else nurtured.
Tools & Components Required For Seed Starting
Seeds require the same inputs as adult plants, only, in smaller quantities. So you will need some way to deliver light, water, nutrients, and heat.
Starting Medium/Starter Plugs
Like mature plants, seeds also need a growing medium to dig their roots into and grow. A very popular option is to buy small cubes of Rockwool, coco coir, or similar growing medium.
These cubes are also called starter plugs. They are spongy cubes that can hold air and water. Each cube has a hole in which you can drop a single seed (or several, depending on the size and type of seed).
The advantage of using cubes or starter plugs is that you don’t have to uproot the seedlings once they are ready for transplantation. You can take the entire cube and place it in a larger container filled with the same material, i.e., Rockwool or coir.
There is also another option in starter plugs, called rapid rooter. This is a moist cube made from organic materials like decomposed tree bark and peat. These may contain beneficial microbes that aid in root growth and nutrient absorption.
Another option is to ditch starter plugs entirely and use a soilless medium like perlite or vermiculite. You can just fill a tray with this material, and plant seeds in them, just as you would in natural soil.
If using rockwool cubes or rapid rooter plugs, you will need multiple small net cups to hold these in. Or you can look for specially crafted trays that contain individual slots for cubes or plugs.
If buying net pots, small 2″ versions work best, as you can keep a lot of them on a small tray.
Since you will be starting a large number of seeds, (anywhere from a dozen to fifty), it is better to look for trays or boxes that can fit these individual cups. Look for containers with a depth of around four to six inches for best results.
There are more advanced options, like building a hydroponic cloner system for your seeds. This is like a miniature hydroponic system, complete with air pumps and everything for your seeds.
For a first attempt though, a simple tray-based system is all you need.
This is for regions where you cannot guarantee a temperature range between 70-90 degrees Fahrenheit at all times during the germinating and starting process.
If you live in a cold area, consider buying a heating mat to be placed under your growing tray. Seeds will refuse to sprout unless the ideal temperature requirements are met.
Again, these are optional components. If it is summer and you have space where the grow tray can get adequate sunlight, you can forego artificial lights entirely. A window sill is often a great place to keep your seeds.
But if sunlight access is not available, get a decently sized grow light that can keep the entire tray surface properly illuminated.
There are several options when it comes to nutrients for seed starting. One option is to use a diluted, half-strength solution of regular hydroponic nutrients.
Or you can go for specialized starter nutrients. There are many brands available, armed with the right mix of nutrients and compounds to encourage root growth and germination.
A Ziploc Bag
This is an optional component to get your seeds to germinate. You may want to try it out to see for yourself whether it has any advantages.
Step-by-Step Instructions – Germinating
1. Prep The Growing Medium
Whether using rockwool, coco coir or rapid rooter cubes, you need to soak them in water to prepare them. Rockwool has a high pH, so you need to wash it in a mixture of vinegar and water to make it suitable for seeds.
Ensure that the cubes are thoroughly moist. For Rockwool and coir, keep them in fresh water for an hour. Rapid rooter cubes can be moistened using a combination of pure water and mild nutrient solution for a few minutes.
2. Place the seeds
There is no guarantee that every single seed you start out with will germinate. So you may want to place at least a couple of seeds in each starter cube.
As an optional step, you can place these wet cubes inside a Ziploc bag and seal them. Place the bag in a dark corner for 2-5 days to allow for germination.
Once that is done, the cubes can be placed in your grow tray. If you opt out of this Ziploc method, simply place the cubes with the seeds in the grow tray, in individual net cups.
3. Add water and nutrients
Fill the bottom of the tray with a mix of pure water and a low concentration of hydroponic nutrients or blooming mixes.
The water level should be high enough to submerge just half an inch of your starter cube and no more. Keep an eye on the water level. If it starts to go down, add more water+nutrients to the tray.
4. Provide adequate light
One of the advantages of a grow tray is its mobility. You can move them around the house if needed. If sunlight is available, you can place them on a windowsill or patio.
If not, just move them indoors and add some grow lights. As the seeds start to sprout, increase the light intensity by bringing the grow lights closer to the tray. Do not bring them closer than six inches though.
Transplanting The Seedlings
Your seedlings are ready for transplantation if their roots are poking out of the cube of growing medium. This stage can take anywhere from a couple of weeks to more than four weeks.
It all depends on the individual plant species. Continue watering your seedlings diligently until they reach this stage. If multiple seeds germinate inside a single cube, look for the healthiest one and remove the others.
Once they are ready, carefully remove the cubes from your grow tray. You should have a working hydroponics system ready by now.
Create some space in the growing medium in your “grown-up” hydroponic system. Place the entire cube with the seedling inside this space.
Gently cover the cube with more growing medium. Water the seedling from the top with a nutrient mix in the first few days. This will encourage the young roots to push into the fresh layers of growing medium for nutrients.
And that’s all there is to it! Your seedlings are ready to grow into big healthy plants in your hydroponic system now!
Learning to get your own seed starter system is not as complicated as learning to create an entire hydroponic system. All you need is some gentle care and attention.
Starting with seeds is definitely cheaper and gives you more freedom. It is also much more satisfying than buying seedlings from the store.
And the best thing is that it takes only minimal input costs and effort. There is no logical reason not to germinate your own seeds for hydroponics.
Buying pre-grown seedlings/saplings is a good option for Hydroponic beginners. But in the long run, learning to start with your own batch of seeds is the best option. We’ll know why.
A Simple Guide to Starting Seeds for Hydroponics
So you’re ready to get started in hydroponics and you’re about to start some seeds…
But you have no idea where to get started?
You’re not alone — when I first started gardening, I was a soil gardener.
Starting seeds for hydroponics systems was unknown to me until I started to build deep water culture and ebb and flow systems. Once I built those, I had to learn how to start seeds hydroponically.
One of the main benefits of hydroponics is the absolute control you have over your growing environment. Knowing that, I didn’t want to germinate seeds in soil and then transplant into a my hydroponic system, adding a bunch of dirt to the system.
There had to be another way.
Here are just a few reasons why you want to start seeds in a hydroponic system as opposed to soil:
- Much cleaner than starting seeds in soil
- Seedlings grow faster after germination
- Easy to transplant into a larger hydroponic system
That second reason is a cool one. As soon as your tap root pops out, a hydroponic system is going to help it grow faster than soil and prevent it from becoming rootbound.
Step 1: Get Your Materials
You don’t need much to get started. If you build your cloner yourself, the rest of the materials will cost you under $50 bucks and will last you for quite a while. If you decide to go with a store-bought cloner, it’ll bump up the cost a bit but you’ll also be getting a much higher quality product.
Seed Starting Materials List
- Hydroponic Cloner – You can either build your own or use something like the Clone King and starter plugs (#3 below)
- 2″ Net Pots
- Rapid Rooter Starter Plugs
- Seeds – find at your local nursery if possible, or buy many places online. A personal favorite of mine is RareSeeds.com
- Air Pump
- Air Stone
Step 2: Fill The Cloner With Water
Fairly simple step here. All you need to do is fill up your reservoir to just under where your net pots sit. Don’t worry about pHing your water or using reverse osmosis right now – standard tap water will be fine.
Step 3: Set Up the Air Pump
Place the air stone in the reservoir and connect the tubing. Connect the other side to the air pump and plug it in. You should see some beautiful bubbles start to come out of the air stone. These bubbles are what will keep the roots of your seeds moist and stimulate growth.
Step 4: Place Starter Plugs and Seeds
Soak each starter plug in some water and then place it in a net pot. The moisture will help the seeds germinate.
Drop 2-3 seeds in each starter plug. We use more than 1 seed because not all seeds will germinate and we want to make sure that every starter plug has a sprouted seed – otherwise we’ll have to replant!
Step 5: Maintenance
This system is very easy to maintain as your seeds sprout.
If you want, you can place a transparent cover over the top to keep in some moisture and increase the temperature of the system, but it’s not necessary.
Make sure to moisten the starter plugs with a few sprays from a spray bottle every day so your seeds have enough moisture to sprout.
When your seeds sprout, clip off all but the strongest seedling from each starter plug.
That’s it! Your seeds should sprout in 3-5 days for most plants and you’ll be ready to start growing some truly epic plants in your hydroponic system in no time!
If you’re more of a visual learner, I have a three part video series from my YouTube channel that goes into the entire setup in detail.
Part One: The Basic Setup
This is the visual version of the blog post. Helpful if you just need to SEE to learn (like me).
Part Two: Making Sure Seeds Germinate
This part of the series talks about some of the maintenance and troubleshooting you might run into when starting seeds, including the infamous “why do they keep falling over” problem that a lot of beginners run into.
Part Three: pH Water and Add Nutrients
This part of the series talks about the need to pH and add nutrients to your reservoir after the seeds have germinated. Because they feed off of their seed leaves at the start of their life, you can get away with not doing this until the seeds germinate.
By the way, I’m using the Bluelab pH Pen to fill all of my pH needs. It’s awesome!
Starting seeds for hydroponics doesn't have to be difficult. In fact, it's really easy! Learn how to do it in 10 minutes with this Epic Gardening tutorial!